1、時鐘部分，TIMER2的時鐘頻率，我是初始化為36M.

RCC_PCLK1Config(RCC_HCLK_Div2); //設置低速AHB時鐘=系統時鐘/2

RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9); // 倍頻系數為9 PLLCLK=8*9=72

2、TIMER初始化

TIM_DeInit(TIM2);

TIM_TimeBaseStructure.TIM_Period = 65535;

TIM_TimeBaseStructure.TIM_Prescaler = 18;

TIM_TimeBaseStructure.TIM_ClockDivision = 0;

TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;

TIM_TimeBaseInit(TIM2, TIM_TimeBaseStructure);

TIM_ICInitStructure.TIM_Channel = TIM_Channel_1;

TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising;

TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;

TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV4;

TIM_ICInitStructure.TIM_ICFilter = 0x0;

TIM_PWMIConfig(TIM2, TIM_ICInitStructure);

TIM_SelectInputTrigger(TIM2, TIM_TS_TI1FP1);

TIM_SelectSlaveMode(TIM2, TIM_SlaveMode_Reset); //復位模式為從模式

TIM_SelectMasterSlaveMode(TIM2, TIM_MasterSlaveMode_Enable); //使能主從模式

TIM_Cmd(TIM2, ENABLE); //使能TIM2計數器

TIM_ITConfig(TIM2, TIM_IT_CC2, ENABLE); //使能CC2中斷請求

3、TIMER中斷處理

void TIM2_IRQHandler(void)

{

/* Clear TIM2 Capture compare interrupt pending bit */

TIM_ClearITPendingBit(TIM2, TIM_IT_CC2);

/* Get the Input Capture value */

IC2_Value = TIM_GetCapture2(TIM2);

}

注意事項：

不知道為什么，STM32的TIMER時鐘經過分頻率后，時鐘的精度誤差會隨分頻值變大而變大。在不分頻的情況下，我檢測1KHz的PWM輸入信號，誤差為0.5us。在18分頻的情況下，誤差已經不能看了。測量100Hz，根據捕獲值計算出來卻是105Hz。

確實如STM32朋友所講，在分頻處我理解錯了，分頻值=TIM_TimeBaseStructure.TIM_Prescaler +1，所以如果要分18分頻，只要將TIM_Prescaler=17即可。經這樣修改后測量誤差在萬分之5以內。謝謝STM32朋友的提醒!!(上面的誤解我就不刪除了，留做以后警記，呵呵!)