/*-------------------------------

溫度控制器V1.5
顯示為三個共陽極LED
溫度傳感器用單總線DS18B20
CPU為2051，四個按鍵，分別為UP，DOWN，SET
溫度調節上限為125度，下限為-55度
只能用于單只18B20

本軟件僅供學習與參考，引用時請注明版權

http://www.cdle.net /> 明浩　2004/1/2
pnzwzw@cdle.net
-------------------------------*/

#include
#include
#define Key_UP P3_0 //上調溫度
#define Key_DOWN P3_1 //下調溫度
#define Key_SET P1_7 //設定鍵（溫度設定，長按開電源）
#define RelayOutPort P3_5 //繼電器輸出
#define LEDPort P1 //LED控制口
#define LEDOneC P3_2 //LED DS1控制（百位）
#define LEDTwoC P3_3 //LED DS2控制（十位）
#define LEDThreeC P3_4 //LED DS3控制（個位）
#define TMPort P3_7 //DS1820 DataPort

unsigned char code LEDDis[]={0xC0,0xF9,0xA4,0xB0,0x99,0x92,0x82,0xF8,0x80,0x90,0xFF,0xBF}; //0-9的LED筆劃,0xFF為空,0xF7為負號

static unsigned char bdata StateREG; //可位尋址的狀態寄存器
sbit DS1820ON = StateREG^0; //DS1820是否存在
sbit SetTF = StateREG^1; //是否是在溫度設置狀態
sbit KeySETDown = StateREG^2; //是否已按過SET鍵標識
sbit PowTF = StateREG^3; //電源電源標識
sbit KeyTF = StateREG^4; //鍵盤是否允許

//sbit KeySETDowning = StateREG^5; //SET是否正在按下
static unsigned char bdata TLV _at_ 0x0029; //溫度變量高低位
static unsigned char bdata THV _at_ 0x0028;
static signed char TMV; //轉換后的溫度值
static unsigned char KeyV,TempKeyV; //鍵值
static signed char TMRomV _at_ 0x0027; //高溫限制
static signed char TMSetV _at_ 0x0026; //溫度設定值
static unsigned char KSDNum; //SET鍵連按時的采集次數
static unsigned char IntNum,IntNum2,IntNum3; //中斷發生次數，IntNum用于SET長按檢測，IntNum2用于設定狀態時LED閃爍
static signed char LED_One,LED_Two,LED_Three; //LED的顯示位 LED_One為十位，LED_Two為個位
static unsigned char Sign; //負號標識

void main(void)
{
void InitDS1820(void); //定義函數
void ROMDS1820(void);
void TMVDS1820(void);
void TMRDS1820(void);
void TMWDS1820(void);
void TMREDS1820(void);
void TMERDS1820(void);
void ReadDS1820(void);
void WriteDS1820(void);
void Delay_510(void);
void Delay_110(void);
void Delay_10ms(void);
void Delay_4s(void);
void V2ToV(void);

StateREG = 0; //初始化變量
SetTF = 1;
PowTF = 1; //關電源
THV = 0;
TLV = 0;
TMV = 0;
KeyV = 0;
TempKeyV = 0;
KSDNum = 0;
IntNum = 0;
IntNum2 = 0;
IntNum3 = 0;
LED_One = 0;
LED_Two = 0;

InitDS1820(); //初始化
ROMDS1820(); //跳過ROM
TMERDS1820(); //E2PRAM中溫度上限值調入RAM
InitDS1820(); //初始化
ROMDS1820(); //跳過ROM
TMRDS1820(); //讀出溫度指令
ReadDS1820(); //讀出溫度值和上限值
TMSetV = TMRomV; //拷貝保存在DS18B20ROM里的上限值到TMSetV

EA = 1; //允許CPU中斷
ET0 = 1; //定時器0中斷打開
TMOD = 0x1; //設定時器0為模式1，16位模式
TH0=0xB1;
TL0=0xDF; //設定時值為20000us（20ms）
TR0 = 1; //開始定時
while(1);
}

//定時器0中斷外理中鍵掃描和顯示
void KeyAndDis_Time0(void) interrupt 1 using 2
{
TH0=0xB1;
TL0=0xDF; //設定時值為20000us（20ms)

LEDPort = 0xFF;
if (!Key_UP)
KeyV = 1;
if (!Key_DOWN)
KeyV = 2;
if (!Key_SET)
KeyV = 3;
//KeySETDowning = 0; //清除
if (KeyV != 0) //有鍵按下
{
Delay_10ms(); //延時防抖 按下10ms再測
if (!Key_UP)
TempKeyV = 1;
if (!Key_DOWN)
TempKeyV = 2;
if (!Key_SET)
TempKeyV = 3;
if (KeyV == TempKeyV) //兩次值相等為確定接下了鍵
{
if (KeyV == 3) //按下SET鍵，如在SET狀態就退出，否則進入
{
//KeySETDowning = 1; //表明SET正在按下
PowTF = 0; //電源標識開
if (!KeyTF)
if (SetTF)
{
SetTF = 0; //標識位標識退出設定
InitDS1820(); //初始化
ROMDS1820(); //跳過ROM
TMWDS1820(); //寫溫度上限指令
WriteDS1820(); //寫溫度上限到DS18B20ROM
WriteDS1820(); //寫溫度上限到DS18B20ROM
WriteDS1820(); //寫溫度上限到DS18B20ROM
InitDS1820(); //初始化
ROMDS1820(); //跳過ROM
TMREDS1820(); //溫度上限值COPY回E2PRAM
}
else
SetTF = 1;
if (!KeySETDown) //沒有第一次按下SET時，KeySETDown標識置1
KeySETDown = 1;
else
KSDNum = KSDNum + 1; //前一秒內有按過SET則開始計數
}
if (SetTF) //在SET狀態下
{
if ((KeyV == 1) (!KeyTF))
TMSetV = TMSetV + 1; //上調溫度
if ((KeyV == 2) (!KeyTF))
TMSetV = TMSetV - 1; //下調溫度
if (TMSetV = -55) //限制溫度上下限
TMSetV = -55;
if (TMSetV >= 125)
TMSetV = 125;
}
if ((!KeyTF) (IntNum3 == 0)) KeyTF = 1; //當鍵盤處于可用時，鎖定
}

if (KeySETDown) //在2秒內按下了SET則計中斷發生次數用于長按SET時計時用
IntNum = IntNum + 1;
if (IntNum > 55) //中斷發生了55次時（大約1.2秒）75為1.5秒左右
{
IntNum = 0;
KeySETDown = 0;
if (KSDNum == 55) //如一直長按了SET1.2秒左右
{
RelayOutPort = 1; //關閉繼電器輸出
PowTF = 1; //電源標識關
LEDOneC = 0;
LEDTwoC = 0;
LEDThreeC = 0;
LEDPort = 0xBF; //顯示--
Delay_4s(); //延時
LEDOneC = 1;
LEDTwoC = 1; //關顯示
LEDThreeC = 1;
Delay_4s();
IntNum = 0;
IntNum2 = 0;
IntNum3 = 0;
}
KSDNum = 0;
}
}
KeyV = 0;
TempKeyV = 0; //清空變量準備下次鍵掃描

if (!PowTF)
{
InitDS1820(); //初始化
ROMDS1820(); //跳過ROM
TMVDS1820(); //溫度轉換指令

Delay_510();
Delay_510(); //延時等待轉換完成

InitDS1820(); //初始化
ROMDS1820(); //跳過ROM
TMRDS1820(); //讀出溫度指令
ReadDS1820(); //讀出溫度值

V2ToV(); //轉換顯示值
if (TMV > TMSetV) //根據采集到的溫度值控制繼電器
{
RelayOutPort = 0;
}
else
{
RelayOutPort = 1;
}